Showing posts with label Mens Wedding Suits. Show all posts
Showing posts with label Mens Wedding Suits. Show all posts

Thursday, January 28, 2010

Discussion about Three Piece Suits!

Let's look at it: the waistcoat has extended long been a lifeless item for most men, but appreciation to resurgence in its fame in men's street wear the suits' waistcoat is back with revenge. Well, not fairly revenge but it is back, it is fine and it is standard. And it means that in 2009 we will observe the comeback of the 3 piece suits, and I couldn't be extra happy. That is for the reason the three-piece suits has been one of the majority under-utilized parts of a man's clothes over the last 40 years.

The 3 piece in 2009 is all about solidity; forget the mismatching fashion rampant in the early parts of the 20th Century and in the 1980s. The comeback of the 3 piece means that the waistcoat has to be traditional and, thus, in the similar fabric as the suits other two pieces. If you do desire to undertaking external of the realm three matching pieces, stick to a same color palette & stay away from any pattern apart from the stripes; you might desire to pair a pinstripe black suits with a pinstripe charcoal waistcoat.

On choosing the perfect 3 piece suits I would advise looking for a waistcoat whose V shape breaks someplace between the sternum and the base of the rib cage. I have seen 3 pieces from the resembling of Giorgio Armani which don't sport the V shape and draw to a close just under the collar, these are going to be a very harder to wear and disregard the traditional subtlety this recovery depends upon. In addition, such a huge waistcoat won't suggest a slim waist as efficiently as one with a deeper neck.

Thursday, November 26, 2009

Fire Tests of Men’s Suits on Racks!

A series of fire tests were conducted to characterize the potential hazard from ignition of men’s suits hanging on racks. The fire test scenario was selected as part of a fire investigation being conducted by the U.S. Department of Treasury’s Bureau of Alcohol, Tobacco, and Firearms. Heat release rate was determined as a function of time from ignition using the oxygen depletionprinciple. In addition, the total heat flux from the burning suits and the mass loss were measured. Three tests were conducted with the suits placed in the open under a large calorimeter. The suits were ignited either in the center or at the end of the rack with a propane torch. Peak heat release rates obtained during the tests ranged from approximately 1 MW to 2 MW.

Introduction to the Fire Test:

Measurement of the rate at which a burning item releases heat is a critical parameter in fire protection engineering. The heat release rate can be used in the characterization of the hazard represented by a given fuel package. Heat release rate can provide information on fire size and fire growth rate. When used as input to a computer fire model, the heat release rate can be used to estimate available egress time and determine detection or suppression system activation time. Heat flux measurements can be used to estimate potential for ignition of adjacent fuel items.

As part of a fire investigation, the U.S. Department of Treasury’s Bureau of Alcohol, Tobacco and Firearms (ATF) was interested in determining the rate of heat release and burning characteristics from a rack of men’s suits. Photographs of the test arrangement showing the racks of suits are presented as figures 1 and 2. Figure 3 presents front and side views of the test arrangement with dimensions illustrating the location of the heat flux sensors.

Results:

The heat release rate curves obtained as a function of time from ignition for the three fire tests. In all three tests, a heat release rate of approximately 1 MW is sustained for about 5 minutes. The peak heat release rate for the first and third tests is about 1 MW while the obtained at the entrance to the exhaust

hood immediately above the center of the burning clothes is shown in Figure 18. During most of


the tests, the temperature above the burning clothes is 150 °C (302 °F). The temperature spikes

briefly to 200 °C (392 °F) during the early portion of the second test. The total heat flux data


obtained from the two sensors in the three tests are shown in Figures 19 and 20. There is good

agreement between the two sensors. Finally, the mass loss rate data for the three tests is presented in Figure 21. The initial mass of suits and racks was 55.8 kg (123 lb), 57.1 kg (126

lb), and 57.6 kg (127 lb) for the first, second, and third tests, respectively. The final mass at the end of the first, second, and third tests was 46.7 kg (103 lb), 48.0 kg (106 lb), and 49.0 kg (108lb), respectivelylb), and 57.6 kg (127 lb) for the first, second, and third tests, respectively.